POUR OBTENIR UN
ET POUR CONNAÎTRE LES PROCÉDURES DE COMMANDE ET DE PAIEMENT, CLIQUEZ ICI!
TO OBTAIN A
AND FOR MORE INFORMATION ABOUT ORDERING AND PAYMENT PROCESSES, CLICK HERE!
INFORMEZ-VOUS SUR LA DISPONIBILITÉ DE PINCES
SPÉCIALES POUR LES TERMINAUX!
INQUIRE ABOUT SPECIAL TERMINAL CRIMPERS!
|
|
| Highway
22 - General Motors (SKU: 500695) |
|
|
Base de panneau G-10
Composantes de panneau - nylon 6/6
filage GXL/XLPE codé selon les couleurs de GM
Étiquettage de filage facile à lire
Expansion possible pour le pouvoir de la batterie et
pour les accessoires
Interface avec vis auto-barrantes
Raccord de l'ensemble des instruments de bord
débranchable
Fil de 8 ga pour l'alternateur
Protection par une méga-fusible de 175 Amp
Relais de 40 Amp pour le ventilateur (HW-22
seulement)
Interrupteurs de démarrage, de phares et des phares
de route
Instructions étape par étape en couleurs qui lient
les raccords aux terminaux (en anglais)
|
G-10 Composite Panel Base
Nylon 6/6 Panel Components
GXL/XLPE GM Color Coded Wire
Easy to Read Wire Labeling
Battery & Accessory Power
Expansion
Self-Locking Screw Clamp Interface
Gauge Cluster Disconnect
8-Gauge Alternator Feed
175 Amp Mega-Fuse Protection
40 Amp Fan Relay (HW-22 only)
Ignition, Headlight, and Dimmer
Switches Included
Full Color, Step-by-Step Instructionss
|
|
 |
|
Description du contenu (anglais seulement,
désolé) / Description of contents
|
|
| 1. |
|
Modular wiring system |
|
| 2. |
|
22 power circuits supported through 15 fuses and 1
circuit breaker |
|
| 3. |
|
Battery and accessory power tap studs provided for
system expansion |
|
| 4. |
|
Panel protected with a 175 amp Mega-Fuse junction
block with a 8 gauge panel feed wire |
|
| 5. |
|
Nylon mechanically secured panel containing
secondary push-back locks, has a 7-1/2” x 4-1/2” footprint, 3-3/8” in
height, and mounted on a (G10) non-conductive epoxy base |
|
| 6. |
|
All power buss bars are constructed of 6 gauge copper |
|
| 7. |
|
All wires are constructed from heat resistant (-60F-
+275F) |
|
| 8. |
|
GXL heavy-wall wire with laser printed circuit
identification every 2 inches |
|
| 9. |
|
GM color coded wires for ease of installation |
|
| 10. |
|
All power circuits wires are 12 gauge constructed |
|
| 11. |
|
New front loaded vibration proof self- locking (Hookes
Law) screw down terminal connection |
|
| 12. |
|
Dedicated battery and ignition circuits for electronic
fuel injection (EFI) Kit contains 3 relays (Horn, Turn Signal & 40 amp Electric Fan or
Fuel Pump) |
|
| 13. |
|
Turn signal and hazard flasher circuits provided |
|
| 14. |
|
8 gauge alternator feed wire provided |
|
| 15. |
|
The kit is set-up for a GM “SI” internally
regulated alternator or GM 1-wire |
|
| 16. |
|
Alternator diode is also provided |
|
| 17. |
|
Kit includes 3 (In-dash Ignition, Headlight &
Alum. Knob and Floor Dimmer) switches |
|
| 18. |
|
GM in-column ignition switch connectors provided,
along with 3-7/8” GM steering column connectors with male and female terminals |
|
| 19. |
|
Plugs directly most 69-74 GM column and most
aftermarket steering columns or use the terminals and connector provided to mate to any
column |
|
| 20. |
|
Spare circuits available (for power windows, locks,
cruise, etc.) |
|
| 21. |
|
Engine compartment (oil pressure, water temp, tach,
starter, neutral safety, brake switch, ignition switch, distributor (GM HEI or Points),
coil, main power and alternator) |
|
| 22. |
|
Chassis wiring (fuel pump, electric fan, headlights,
running lights, brake lights, 3rd brake lt., directional, license plate, radio, heat &
AC, and wipers) |
|
| 23. |
|
Full color schematic of overall vehicle wiring along
with individual harness subkit instructions for trouble-free installation. |
|
|
